|
(三)东莞移印机研磨刮刀刀口操作步骤
1.刀口放在研磨板上
Z.注入3至5滴研磨液
3.放上杯型磁环
4.调较压力
5将四支手指放进杯内带动磁环以逆时针方向转动
并围绕铁板周边运行约10-60秒钟。
(3) Or.Blade Abrasion Procedure:
1. Put the blade on the abrasion board.
Z. Inject 3-5 drops of abrasion liquid.
3. Put on the cup-shaped magnetic cup
4. Adjust the pressure.
5. Insert 4 fingers into the magnetic cup, revolve
the cup at anti-clockwise direction and move
along the edge of the abrasion board for 10-60
seconds simultaneously.
东莞移印机常遇问题及解决方法
(4) Common Problems and Solutions
┌─┬─┐
│B │〔│
┌──────────────────────────────┬─┼─┼─┼─┐┌─┬───┐
│刮油不清Unclean Scrapping │. │. │. │ ││ │ │
├──────────────────────────────┼─┼─┼─┼─┤├─┼─┬─┤
│漏油Ink Leakage │. │ │ │ ││ │ │ │
├──────────────────────────────┼─┼─┼─┼─┤├─┼─┼─┤
│惰刀(图案太大时，油墨厚度不均) │. │ │ │. ││. │ │ │
│Blade Laziness (print area too large, uneven ink thickness) │ │ │ │ ││ │ │ │
├──────────────────────────────┼─┼─┼─┼─┤├─┼─┼─┤
│研磨刀口时间太长，办不能解决问题 │ │ │ │ ││ │ │ │
│Abrasion time too long, problems cannot be solved │ │ │ │ ││ │ │ │
├──────────────────────────────┼─┼─┼─┼─┤├─┼─┼─┤
│图案有拉丝现象Wiredraw Problem │ │. │ │ ││ │. │. │
└──────────────────────────────┴─┴─┴─┴─┘└─┴─┴─┘
解决办法:
东莞移印机A.研磨刀口10-60秒不等
B稀释油墨
〔.加添油墨
D.调轻压力(逆时针转)
E.加重压力(顺时针转)
卜重新安装钢片(保持清洁
G.选用lOmm厚钢板
H.图案加网点使用
I.清理刀口油溃
J.刀口过阔，磨尖刀口
}SOIUCIOnS:
A. Abrade the Dr.Blade for 10-60 seconds
B. Dilute the ink
〔.Add ink
D. Adjust the stroke pressure (anti-clockwise direction.)
E. Increase stroke pressure(turn clockwise)
F Re-install the steel plate(keep clean)
G. Choose a lOmm thick steel plate
H. Make screen of the printing pattern
I. Clean the Dr.Blade
J. Blade too wide, sharpen the blade
东莞移印机注意事项:
1刀口阔度请保持0.15-0.7mm
Z.调较压力，刀口与磁芯高度，标准为Z.Smm，可增减一
转使用，每转为1.Smm(每转动旋转板手一个阔度即
12mm，相等高度O.lmm，每次调较为二个至四个
阔度，即0.2mm至0.4mm)
3.安装钢片应保持清洁。
4.每次研磨刀口寿命因不同颜色油墨及钢片新旧和压力不
同之损耗而有不同，一次研磨约可刮油3000-10000次
不等。
5.油杯应保持转动约不少于500次为一转。
6.油杯工作时应转松杯顶排气旋钮。
7.操作时应小心保持刀口不被碰撞。
Remarks:
1. Maintain the width of the blade in 0.15-0.7mm.
2. Adjust the pressure,the standard height of blade and magnetic dome
should be 2.5mm (+/-1.5mm/1 round)(The width for every turn of
the handle is 12mm; equal to the height of O.lrnm, it is advised to
adjust 2 to 4units at a time, i.e.0.2mm to 0.4mm each time.)
3. Keep clean when installing the steel plate.
4. The abrasion life of the blade subjects to the different depreciation
of ink color,age of steel plate and the pressure, every abrasion can
afford 3000 to 10000 scrappings.
5. Maintain the ink cup revolution not less than 500 times for a round.
6. When working，release the ink cup exhaustion screw.
7. Prevent the blade from collision during operation.
东莞移印机 |